length tolerance
英 [leŋθ ˈtɒlərəns]
美 [leŋθ ˈtɑːlərəns]
网络 长度容差; 长度公差; 長度公差
双语例句
- A linear unit based on the length or width of the human hand. To govern with the right extent of tolerance is an art.
长度单位以手掌的长度或宽度为依据。掌握宽的尺度是一门学问。 - A chirp grating is placed inside a multimode interference ( MMI) structure to shorten the device length and increase wavelength tolerance.
为了缩短组件长度并增加波长变动容忍度，我们在多模干涉结构里面旋转一个周期渐变光栅。 - Variation of coleoptile length in winter wheat varieties under PEG simulated drought stress and its association with their drought tolerance
模拟干旱胁迫下冬小麦胚芽鞘长度变化及与抗旱性的关系研究 - This paper focuses on the discretization of three-dimensional parametric curves, which is used widely in the fields of computer graphics and surface mesh generation, and the algorithms are presented here according to the arc length rule and a specified discretization tolerance.
针对在计算机图形学和曲面网格生成中广泛应用的三维参数曲线离散算法进行了研究，分别给出了曲线按弧长原则和精度原则进行离散的实施过程。 - The tests also showed that in the presence of MSD, the residual strength of the structure, critical crack length and even crack propagation life are greatly reduced in comparison with the isolated cracks considered by the current damage tolerance requirements.
MSD使剩余强度明显降低，临界裂纹尺寸大大减小，裂纹扩展寿命显著缩短，从而使损伤容限能力减退，破损安全不复存在。 - The effective pile length was proposed, and the relation between the tolerance of pile top settlement with it was discussed in a systematic way.
提出LDBPs有效桩长的概念，系统分析有效桩长与桩顶容许变形的关系。 - The major ear seed setting rate as the direct idex of cold tolerance is reliable, anthes length and anther volume can be as the indirect index of cold tolerance.
主穗结实率可直接作为孕穗耐冷性的评价指标，花药长、花药体积可间接作为孕穗期耐冷性指标。 - Then by taking the regular square prism as an example, the machining error is analyzed, and the relationship among the length of the lathe tool, the work dimension and the tolerance is obtained.
螺纹自动退刀安全防撞装置以车削正四棱柱为例，进行了误差分析，得到了刀具长度与工件尺寸和容许误差间的关系。 - The radicle length stressed at 38 ℃ for 60~ 72 h could be taken as one of the hot tolerance assessment indexes.
38℃下胁迫60～72h的胚根长可作为黄瓜耐热性鉴定指标之一。 - The Calculation of the Measured Value on the Base Tangent Length and Its Tolerance for the Involute Splines
渐开线花键公法线长度测量值及其公差的计算 - The fatigue strength of the tested chain increases about 80%: The remanent tensile deformation is very small and the length accuracy may be ensured by pre-adjusting the pitch tolerance of link plate dies.
疲劳强度可提高80%左右。预拉后的链条的残余伸长量不大，完全可预先对链板冲模具节距尺寸作适当的调整，以保证链长精度。 - The relationship between the screwing length of screw thread and the pitch error, screw linearity error, screw precision and screw tolerance is discussed to explain how to select the screwing length of screw thread in actual applications.
对螺纹旋合长度与螺距误差、螺纹直线度误差、螺纹精度及螺纹公差的相关联系进行分析，说明螺纹旋合长度在实际中的选择应用。 - These QTLs cause the increase of culm length, panicle length, spikelets per panicle and panicle exsertion under low temperature, showing that these QTLs are correlated with cold tolerance.
这些主效QTL在低温环境下对水稻秆长、穗长、穗粒数和穗抽出度有增效作用，与水稻耐冷性有一定的相关性。 - Results show that the circle prefix which has arbitrary length can increase the quality of received eye diagram and improve the dispersion tolerance. The power equalization has been used to eliminate the performance differences of channels.
仿真结果表明，循环前缀的插入提高了眼图的性能、改善了色散容限；针对不同子载波进行功率均衡能够有效减小信道间的性能差异。 - The study of the transgenic Arabidopsis germination rate, root length, salt-tolerant overall plants showed that the gene in a certain level enhanced the transgenic Arabidopsis salt tolerance.
通过对转基因拟南芥的萌发率、根长、整体植株的耐盐性的功能研究，显示该基因在一定水平上提高了转基因拟南芥的耐盐性。 - The root length is main parameter of root architecture with various important functions such as nutrient uptake, drought tolerance and yield.
而根的长度是根型的主要参数，对于养分的吸收，耐旱和作物的产量都有重要的作用。 - This structure can ensure the cavities with high homogeneity of electrical parameters in the length direction of slow-wave structure, and can limit the tolerance range in the assembly of the slow-wave.
这种结构可保证谐振腔电动参数在慢波系统长度上的高度均匀性，而且在装配慢波系统各段时可以限定公差变化范围。